Ts 480hx manual

Quick Links. See also: Service Manual , Reference Manual. This equipment requires a licence and is intended for use in the countries as. Table of Contents. Previous Page. Next Page. Kenwood TS User Manual 60 pages. The use of the warning symbol means the equipment is subject to restrictions of use in certain countries. Confirm your local amateur radio regulations and requirements before operating the transceiver.

For example, each time you change the Menu No. Immediately turn the power OFF and remove the power cable. Stop the car and then perform transceiver configuration. The transceiver can give excellent results if the antenna system and its installation are given careful attention. If a fuse blows, determine the cause then correct the problem. Only after the problem has been resolved, replace the blown fuse with a new one with the specified ratings.

As for the supplied microphone, fully insert the modular connector into the MIC jack until the locking tab clicks. You can External speaker Opt. Reading these two pages should get your voice Amateur radio band.

SP jack Mate with a 3. The TSHX is equipped with 2 cooling fans. Air flows in from these fans. If you wish to use a commercially available 3rd party angle or mount, there are 4 screw holes available on the rear of the Remote Control panel so that you can mount it to the angle or mount.

The purpose of the Squelch is to mute the speaker when no signals are present. The S-meter scale appears when then speak into the microphone in your normal tone the transceiver is in reception mode, and the PWR of voice. The range is from 0 to with a default of QUICK MENU Many functions on this transceiver are selected or Because the number of functions this transceiver configured via a software-controlled Menu, rather provides is extraordinary, there are numerous items in than through the physical controls of the transceiver.

Compared with other voice UHF frequencies. Although long distance DX depending on whether the other station is using wide contacts may be less common while using AM, the band or narrow band filter for FM mode.

Auto Zero-beat automatically and exactly when communicating under worst conditions. It may matches your transmit frequency with the station you be true that newer digital modes rival CW as being are receiving. The required tone frequency differs among repeaters.

Repeaters also differ in their requirements for either continuous or burst tones. To avoid this, select an VOX eliminates the necessity of manually switching appropriate delay time that allows all of your to the transmission mode each time you want to words to be transmitted without an overly long Selecting the appropriate speed is switching between transmission and reception important in order to send error-free CW that other modes.

You can also change the configure the transceiver to change the operating interval playback time of the message. RTTY is the data communications mode with the longest history. Instead of trying to describe your station, simply showing it is much faster.

Transmitting images over the air requires a scan converter, besides a transceiver. Interference adjacent to the desired signal can be reduced by — Using DSP filtering AF , you can control the bandwidth, cancel the multiple jamming beat, and reduce the noise level , t using DSP filtering technology.

It is used to inhibit transmit data from the transceiver when the computer is not ready to receive data. Transmit data is inhibited when the level is low. CTS: This signal is applied from the transceiver. It is used to inhibit transmit data from the computer when the transceiver is not ready to receive data. Transmit data is stopped when the level is low. A bit is the smallest piece of information that a computer can handle. A byte is composed of eight bits. This is the most convenient form for most computer data.

This data may be sent in the form of either serial or parallel data strings. The parallel method is faster but more complicated, while the serial method is slower and requires less complicated equipment. The serial form is, therefore, a less expensive alternative. Serial data transmission uses time-division methods over a single line. Using a single line also offers the advantage of reducing the number of errors due to line noise. Only 3 lines are required theoretically for control of the transceiver via the computer:.

From a practical standpoint, it is also necessary to incorporate some means of controlling when this data transfer will occur. The computer and transceiver cannot be allowed to send data at the same time! To interface between the TS transceiver and a PC, use a commercially available cable with a DB-9 female connector at each end.

Each connector pin must be connected to the same pin number at the other end a straight cable. To control the transceiver from a PC, utilize the general purpose terminal program to send commands to the tranceiver. The transceiver responds the command accordingly. You can further develop or create a script of the commands using a macro function of the terminal program.

You can download the program for free and try it out on your PC. A computer control command is composed of an alphabetical command, various parameters, and the terminator that signals the end of the control command. Program execution may be delayed while turning the Tuning control rapidly. A command consists of 2 alphabetical characters. You may use either lower or upper case characters. Parameters are used to specify information necessary to implement the desired command.

The parameters to be used for each command are predetermined. The number of digits assigned to each parameter is also predetermined. Note: If a particular parameter is not applicable to this transceiver, the parameter digits should be filled using any character except the ASCII control codes 00 to 1Fh and the terminator ;.

To signal the end of a command, it is necessary to use a semicolon ;. The digit where this special character must appear differs depending on the command used. In addition to the Answer command, the transceiver can send the following error messages. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up.

Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.